Universal Laser Systems Laser Platform M-300 Guia de Resolução de Problemas Página 25
- Página / 100
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7
6
5
I
2
3
4
8
9
9
10
11
13
14
14
12
10
15
System Operation 3-5
Before you assume that the Laser Cartridge is the source of decreased laser power, consult the
Troubleshooting Guide in the back of this manual first to help you determine the exact cause. If,
after consulting the Troubleshooting Guide, you cannot resolve the issue or determine the
cause of the problem, please contact your dealer or our Customer Support Department directly.
7) Motion System
The motion system consists of the mechanically moving parts of the laser system. It is made up
of rails, motors, bearings, belts, mirrors, a lens, home sensors, and other parts. There are two
directions of motion, left and right is called the “X-axis”, front to back is called the “Y-axis”, and
the movement of the engraving table up and down is called the “Z-axis”.
(1) X-axis Rail (Arm)
(2) X-axis Motor and Drive Gear
(3) X-axis Bearings
(4) Focus Carriage
(5) X-axis Belt
(6) X-axis Idler Pulley
(7) #2 Mirror
(8) #3 Mirror and Focus Lens
(9) Y-axis Bearing(s)
(10) Y-axis Rail(s)
(11) Y-axis Motor
(12) Y-axis Belt
(13) Y-axis Idler Pulley(s)
(14) Y-axis Drive Gear(s)
(15) Y-axis Shaft(s)
The CPU controls the movement of the motors, which moves the mirrors and Focus Lens
across the engraving area and over the material. At the same time, it is synchronizing the laser
pulses with the position of the Focus Lens. It is this precise positioning and timing of the laser
pulses that produces the highest quality and fastest speed of engraving.
The Focus Carriage contains the #3 Mirror and the Focus Lens. This is the laser beams final
exit point. The Focus Carriage delivers the laser beam to the material in the X-axis direction by
traveling along the X-axis Rail. The Focus Carriage moves in the Y-axis direction as a result of
the entire X-axis Arm moving along the Y-axis rails. Coordinated efforts between X-axis and Y-
axis movements can position the Focus Carriage anywhere in the engraving area at a maximum
resolution of 1000 DPI.
8) Material Applications
These are operator provided materials that will be engraved or cut by the laser system. Not all
materials are suitable for CO2 laser engraving or cutting. Please refer to the Material
Applications Guide for a listing of sample materials and sample printer driver settings to get you
started using various materials.
WARNING: Some application materials, when laser processed, can possibly
ignite, produce abrasive particles, and/or produce toxic or caustic gases. It
is the operator’s responsibility to read all manufacturer warning labels or
contact the manufacturer of the material directly to verify that the material is
safe to laser process.
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Manuais e produtos relacionados com Níveis laser Universal Laser Systems Laser Platform M-300
(14 páginas)Bosch SMV86P00DE Exclusiv Made in Germany ActiveWater Ge manuály
Uživatelské manuály a uživatelské příručky pro Myčky nádobí Bosch SMV86P00DE Exclusiv Made in Germany ActiveWater Ge.
Poskytujeme 3 manuály pdf Bosch SMV86P00DE Exclusiv Made in Germany ActiveWater Ge ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais