Universal Laser Systems Laser Platform M-300 Guia de Resolução de Problemas Página 8
- Página / 100
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
1-2 Safety
• Dangerous voltages are present within the electronics and laser enclosures of this
system. Although access to these areas is not necessary during normal use, if it becomes
necessary to open one of these enclosures for service reasons please remember to
disconnect the power cord from your electrical supply.
• Care should be taken when moving or lifting this device. Obtain assistance from 1 or 2
additional people when lifting or carrying. Severe bodily injury may occur if improper lifting
techniques are applied or the system is dropped.
• This device is specifically designed to comply with CDRH performance requirements
under 21 CFR 1040.10 and 1040.11. CDRH is the Center for the Devices of Radiological
Health division of the Food and Drug Administration (FDA) in the USA. It also complies with
CE (European Community) safety regulations. No guarantees of suitability or safety are
provided for any use other than those specified by Universal Laser Systems, Inc.
Laser Safety
• The device contains a sealed carbon dioxide (CO2) laser in a Class I enclosure that
produces intense invisible and visible laser radiation at a wavelength of 10.6 microns in the
infrared spectrum. For your protection, this enclosure has been designed to completely
contain the CO2 laser beam. However, the intense light that appears during the engraving
or cutting process is the product of material combustion or vaporization. DO NOT STARE
AT THE BRIGHT LIGHT OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
• This device may contain a visible red laser diode (Class IIIa). DO NOT STARE AT THE
RED LIGHT OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
• The user door is safety interlocked and will disable the invisible CO2 laser beam from firing
when the user door(s) are opened. However, since the red diode laser produces visible light,
is NOT safety interlocked and can be activated with the door(s) either open or closed.
• Do not operate any system that has had its safety features modified, disabled, or removed
as this can expose your eyes and skin to invisible and visible CO2 laser radiation which can
cause permanent blindness and/or severe burns to your skin.
• Improper use of controls and adjustments, or performance of procedures other than those
specified in this manual, may invalidate the safety of this system.
Safety Labels
CDRH and CE regulations require all laser manufacturers to affix warning labels in specific
locations throughout the equipment. The following warning labels are placed on the laser
system for your safety. DO NOT remove them for any reason. If the labels become damaged
or have been removed for any reason, DO NOT OPERATE the laser system and immediately
contact Universal Laser Systems, Inc. for a free replacement. Labels are NOT to scale
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Manuais e produtos relacionados com Níveis laser Universal Laser Systems Laser Platform M-300
(14 páginas)Panasonic TX32PS10D manuály
Uživatelské manuály a uživatelské příručky pro Audio Panasonic TX32PS10D.
Poskytujeme 3 manuály pdf Panasonic TX32PS10D ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais